Paper ID

Technical Session – I

Fluid Mechanics

01 November 2013 Friday 2:00-4:00 PM

Venue: Room # A

Chair: Prof. Yos Morsi (SUT, Australia)

Co-chair: Prof. Dr. Md. Mahbub Alam (HIT, China)

Page #

FM-01

Application and Analysis of Marine Water Jet Propulsion

Md. Jiaur Rahman (BUET, Bangladesh)

FM-02

Effects of Fibrous Cap Thickness and Stenosis Severity on the Fluid and Structural Behavior in a Model Stenosed Artery                                                                      M. Rejaul Haque (BUET, Bangladesh)  M. Emran Hossain Bhuiyan (BUET) A.B.M. Toufique Hasan (BUET)

FM-03

Experimental Analysis on Minor Head Loss for Flow Through Locally Manufactured Ball Valve for Supplying Fluid in Bangladesh

Sadia Haque (BUET, Bangladesh)  M. Q. Islam (BUET)

FM-04

Flow Topology Around Two Square Cylinders in Side-By-Side Arrangement

Md. Mahbub Alam (HIT, China)

FM-05

Reduction of Fuel Consumption of a Car by Aerodynamic Drag Reduction                                                                              Mohammad Mashud (KUET, Bangladesh) Abdullah Al Bari (KUET) Md. Shahadot Hoshen (KUET)

FM-06

Analysis of Flow in Complex Pipe System

Abdul Mohaimen Safi (BUET, Bangladesh)

FM-07

Numerical Study of Laminar Boudary Layer Using Navier Stokes Equation and Finite Volume Method

Toukir Islam (BUET, Bangladesh)  Md. Minal Nahin (BUET) Md. Abu Abrar (BUET)

FM-10

Flow Separation Control on NACA 0015 Airfoil Using Plasman Vortex Generator

C. W. Wong (HIT, China) L. J. Wang (China) Z. Wu (China) C. H. Li (China) Q. Sun (China) M. M. Alam (China) Y. Zhou(China)

FM-11

Hydrodynamic Analysis of Wave Impact Forces and Overturning Moment on Monopile Foundations of Offshore Wind Turbines

Md. Shahidul Islam (BUET, Bangladesh) Gazi Md. Khalil (BUET)

FM-12

Effect of Roughness Height on the Turbulence Models for Ahmed Car Body Simulation

Abul Kalam Azad (KUET, Bangladesh) Mohammad Arif Hossain (KUET) AKM Sadrul Islam (IUT, Bangladesh)

FM-13

Flow Over Circular Cylinders in Axial Flow with Different Nose Shapes                                                                                               Qin Sun (HIT, China) Md. Mahbub Alam (China) C.W. Wong (China) Y.Zhou (China)

Paper ID

Technical Session – II

Energy Technology – I

01 November 2013 Friday 2:00-4:00 PM

Venue: Room # B

Chair: Prof. Dr. Md. Tajul Islam (CUET, Bangladesh)

Co-chair: Prof. Dr. Nirendra Nath Mustafi (RUET, Bangladesh)

Page #

ET-01

Implementation  Procedure and Financial Model of Solar Mini Grid at Rural Areas in Bangladesh                                                                                                              S.M. Najmul Hoque (RUET, Bangladesh) Barun Kumar Das (RUET) Mohd. Rafiqul Alam Beg (RUET) Roqibul Isalm (SED, GIZ , Bangladesh) 

ET-04

Performance of Nanofluid with Different Nanoparticles Inside a Solar Collector

Rehena Nasrin (BUET, Bangladesh) Salma Parvin (BUET) M.A. Alim (BUET)

ET-13

Renewable Energy in Rural Development

M. A. Zobaer (BUET, Bangladesh) M. A. R. Sarkar  (Bangladesh)

ET-14

An Investigation on the Production of Brown Gas (HHO) as an Alternative Automotive Fuel by Water Electrolysis

Mustafi Nirendra N. (RUET, Bangladesh)Amin Md. Ruhul (RUET)Ahmed Md. Zakaria(RUET) Islam Md. Mayeedul(RUET)

ET-17

Design, Fabrication and Performance Test of an Improved Solar Water Heater

K. H. Pulok (RUET, Bangladesh) S. N. Shaily (RUET) M. M. Hasan (RUET) Manik (BUET) Md. Shamim Akhter (RUET)

ET-24

Development of a Novel Water Treatment Technique Using Solar Still Cum Sand Filter

Abdullah Al Sadeek (KUET, Bangladesh) Kh. Mahbub Hassan (KUET) Md.IftekarAlam (KUET) Md.Atiqur Rahman (KUET)

ET-25

Design and Fabrication of a Solar Agricultural Water Pumping System and Cost Comparison with Diesel Pumps

Md. Saifur Rahman (CUET, Bangladesh) Juwel Chandra Mojumder (CUET) Md. Yousuf Mia (CUET) Romel Barua (CUET) Anamul Hossain (CUET)

ET-27

Hybrid Energy Modeling for Auto Vehicles

Necolus Shaha (DUET, Bangladesh) Md. Bashir Uddin (DUET)

ET-28

Low Voltage Ride Through (LVRT) Capability Improvement of Wind Power Generator by Using STATCOM

Md. Hasanuzzaman (RUET, Bangladesh) M.R.I. Sheikh (RUET)

ET-29

Design, construction and performance test of a portable solar cooker                        M.A. Kader (RUET, Bangladesh) Raju Ahamed (RUET) B.K. Das (RUET) M.E. Hoque (RUET) S.M.N. Hoque (RUET) M.A.Rahim (RUET) S.M. Rasid (RUET)

ET-30

Solar Cooling System: Progress, Prospect and Future Directions

Satyajit Mojumder (BUET, Bangladesh) Sourav Saha (BUET) M. M. Rahman (UM, Malaysia) M.A.H. Mamun (BUET)

ET-32

Study on Energy Situation in Bangladesh                                                                    M. Alauddin Al Azad (KUET, Bangladesh) Niamat Ullah Ibne Hossain (KUET) Md.Ridwan Mahmud (KUET)

Paper ID

Technical Session – III

Material Science- I

01 November 2013 Friday 2.00-4.00 PM

Venue: Room # C

Chair: Prof. Siddhaartha Mukherjee (Jadavpur University, India)

Co-chair: Prof. Dr. Md. Shamimur Rahman (RUET, Bangladesh)

Page #

         MS-05

Separation of Silica from Local Clay                                                            

Hosne Ara (BUET, Bangladesh) Tasmia Zaman (RUET, Bangladesh) A.S.W. Kurny (BUET)

MS-08

Improved Dielectric Properties of La/Mn Codoped Bismuth Titanate Ceramic

M. S. Parvez (Bangladesh) M. Bodiul Islam (Bangladesh)

        MS-14

Effect of Composition and Sintering Temperature on the Microstructure and Theoretical Density of Titania Stabilized Alumina Cutting Tool.

Abu Naser Rashid Reza  (BUET, Bangladesh) Tashneem  Ara Islam (RUAS, Germany)  Md. Fakhrul Islam (BUET) Md. Mohar Ali Bepari (BUET)

        MS-15

Corrosion  of  Galvanized Steel and Its Subtitutes in Various Environments

M. Merajul Haque (BUET, Bangladesh) S. Alam Limon (BUET) M.Moniruzzaman (BUET) Md. Mohar Ali Bepari (BUET)

        MS-19

Studies on the Artificial Ageing and Microstructure of the Al-6Si-0.5Mg Alloys with Copper Addition at Various Levels

A. Hossain (BUET, Bangladesh) M. S. Kaiser (BUET) A. S. W. Kurny (BUET)

        MS-20

Influence of Copper and Nickel Addition on Microstructure and Artificial Ageing of Al-6Si-0.5Mg Alloys                                                                         

A. Hossain (BUET, Bangladesh) M. S. Kaiser (BUET) A. S. W. Kurny (BUET)

        MS-23

Formation of Perovskite Structure and Microstructure Development of Nb Doped BaTiO₃ Based Ceramics                                                                         

 A. N. Ahmed (BUET, Bangladesh) H. M.M.A. Rashed (BUET)

MS-25

  Surface Alloying of CP-Ti Using preplaced Fe-C-Si powder by Tungsten Inert Gas Torch Technique

M.A Maleque (IIUM, Malaysia) S.A. Adeleke (IIUM, Malaysia)

MS-29

Design and Fabrication of an Experimental Set-Up to Measure Carbon Content of an Alloy                                                                                                        

Md. Yousuf Mia (CUET, Bangladesh) J. C. Mojumder (CUET) Md. Saifur Rahman (CUET)Anamul Hossain (BUET, Bangladesh) Romel Barua(BUET)

MS-38

Stress Analysis of an Internal Grooved Pressure Vessel                           

 Abdul Mohaimen Safi (BUET, Bangladesh)

MS-39

Evaluation of Start of Crack Growth of Aluminum Alloy using Optical Microscopy

Md. Nurul Islam (RUET, Bangladesh), Sadia Afrin (RUET) and Ananya Rani Kundu (RUET)

MS-48

Optimization of Process Parameters of Shielded Metal Arc Welding (SMAW) For Stainless Steel Welding

 Naseem Ahmed (KUET, Bangladesh) Soumen Halder (KUET) Md. Asadul Islam (KUET) Niamat Ullah Ibne Hossain (KUET)

Paper ID

Technical Session – IV

Thermal Engineering

01 November 2013 Friday 2.00-4.00 PM

Venue: Room # D

Chair: Dr. Firoz Alam (RMIT, Australia)

Co-chair: Dr. Altab Hossain (UM, Malaysia)

Page #

          TE-02

Finite Difference Solution of the Transient Free Convection in Micropolar Fluid with Heat Generation and Constant Heat Flux

GM Rashid (KUET, Bangladesh) MM Alam (KU, Bangladesh) MA Hossain (KUET)

         TE-03

Enhancement of Higher Evaporating Temperature of Household Refrigerator using Phase change Material

Md. Imran Hossen Khan (DUET, Bangladesh) Hasan M.M. Afroz (DUET) Md. Mostafizur Rahman (DUET)

          TE-04

Aspen-Hysys Simulation of a Condensate Fractionation Plant

Sukanta Kumar Mondal (SUST, Bangladesh) M. Rakib Uddin (SUST)  A. K. Azad (CQU, Australia)

         TE-05

Conjugate Effect of Convection and Conduction in a Nanofluid–Filled Complicated Cavity

Salma parvin (BUET, Bangladesh) Rehena Nasrin (BUET) M. A. Alim (BUET)

         TE-07

Experimental Investigation and Prediction of Heat Transfer in Turbulent Flow through Tube with Conical Ring Inserts

Saddam Hossain Khan (BUET, Bangladesh) M. A. Rashid Sarkar (BUET)

TE-09

Heat Absorption and Joule Heating Effect along a Vertical Wavy Surface on MHD Free Convection Flow with Viscosity Dependent on Temperature

N. Parveen (BUET, Bangladesh) M. A. Alim (BUET)

          TE-11

Design, Construction and Testing of a Port Fuel Injection (PFI) System for a Four Cylinder SI Engine

Md. Syed Ali Molla (KUET, Bangladesh) Mohd. Sapuan Salit (UPM, Malaysia) G.M. Sutan Mahmud Rana (KUET)

         TE-12

Performance Test of a Diesel Engine with Different Esters of Alternative Fuel

S.M. Najmul Hoque (RUET, Bangladesh) Mohd. Rafiqul Alam Beg (RUET) Barun Kumar Das (RUET) S.M. Rasid (RUET)

TE-14

Design Operation and Maintenance of Potato Cold Storage in Bangladesh

Md. M. Islam (BUET, Bangladesh) Md. M. M. Hasan (BUET) M A R Sarkar (BUET)

TE-16

Performance evaluation of PV Module Using Water Filters and Infrared Reflective Glass Covers

Y. Baradey (IIUM, Malaysia) M.N.A.Hawlader (Malaysia) M. Idresand S. I.Ihsan (Malaysia)

         TE-17

Investigation of Condensation Heat Transfer Characteristics for R1234ze(E), R32, R410A and Zeotropic Mixture of R1234ze(E) and R32 inside Smooth Tube

Md. Anowar Hossain (DUET, Bangladesh) Akio Miyara (JU, Japan) Md. Zahidul Sarkar (DUET) Md. Jahangir Alam (DUET)

Paper ID

Technical Session – V

Applied Mechanics - I

01 November 2013 Friday 4:15-6:30 PM

Venue: Room # A

Chair: Prof. Masaya Takasaki (Saitama University, Japan)

Co-chair: Dr. Md. Rokunuzzaman (RUET, Bangladesh)

Page #

AM-01

Investigation of the Effect of Composite Bed on Milling Machine to Reduce Chatter

Adib Bin Rashid (IUT, Bangladesh) Hasibul Shams (IUT) Abdur Rashid Tipu (Bangladesh) Mohammad Reyad Arefin (IUT)

AM-05

Effect of Frequency and Amplitude of Vibration on Ring-Traveller Friction of Ring Spinning Frame                                                                                    Hosne Ara Begum (Bangladesh) Prof. Dr. Md. Maksud Helali (Bangladesh) Abu Bakr Siddique (Bangladesh)

AM-07

Development of an Automatic Humidity Control System

M.E. Hoque (RUET, Bangladesh) S.M. Rasid (RUET) Amit Roy (RUET) N. Paul (RUET) Ferdous Alam (RUET) Md. Raseluzzaman (RUET)

AM-08

Design & Performance Analysis of a Smart Portable PV Charger         Md. Abu Shahab Mollah (AUST, Bangladesh) M. A. Parvez Mahmud (UST, South Korea) Md. Faysal Nayan (KUET, Bangladesh) Shahjadi Hisan Farjana (KUET, Bangladesh) Sharmin Sobhan (AUST, Bangladesh)

AM-12

Development of Automatic Smart Waste Sorter Machine

Mahmudul Hasan Russel (CUET, Bangladesh) Mehdi Hasan Chowdhury (CUET) Md. Shekh Naim Uddin (CUET) Ashif Newaz (CUET) Md. Mehdi Masud Talukder (CUET)

AM-13

Improvement of Vibration Isolation Characteristics Using Acceleration Feedback Based on Kalman Filter Estimation

M. M. Zaglul Shahadat (Saitama University, Japan) T. Mizuno (SU,) Y. Ishino (SU) M. Takasaki (SU)

AM-16

Tactile Feedback Using Surface Acoustic Wave

Masaya Takasaki (Saitama University, Japan) Takeshi Mizuno (SU)

AM-18

An Analytical Study of Passive Anti-Roll Tanks

Gazi Md. Khalil (BUET, Bangladesh) Syed Marzan-ul Hasan (YNU, Japan) Md. Ehsan Khaled (YNU)

AM-20

Implementation of Drive by Wire Technology Replacing the Conventional Vehicle Control System

Ahmad Hasan Jarjis (KUET, Bangladesh) Md. Zonayed Hossain (KUET)  G.M Sultan Mahmud Rana (KUET) Niamat Ullah Ibne Hossain (KUET)

AM-22

Harvesting Energy from Sound and Vibration                                              Arifur Rahman (RUET, Bangladesh) M. E. Hoque (RUET)

Paper ID

Technical Session – VI

Industrial Engineering – I

01 November 2013 Friday 4.15-6.30 PM

Venue: Room # B

Chair: Prof. Abdul Ghafoor (NUST, Pakistan)

Co-Chair: Prof. Dr. Md. Mosharraf Hossain (RUET, Bangladesh)

Page #

IE-01

Inventory System with Postponed Demands Considering Reneging Pool and Rejecting Buffer Customer                                                                     Mohammad  Ekramol  Islam (NU, Bangladesh) K.M Safiqul Islam (DSH, Bangladesh) M Sharif Uddin (JU, Bangladesh)

IE-02

Bank Management Under Data Mining Environment Towards Fraud Detection                                                                                                  Md.  Sarwar  Kamal (TU, Bangladesh) Md. Aktar kamal (IUT, Bangladesh) Sonia Farhana Nimmy (IUT, Bangladesh)

IE-05

Inventory System with Postponed Demands and Service Facilities-MAM Approach

Mohammad Ekramol Islam (NU, Bangladesh)

IE-11

Applying Genetic Algorithms to Resolve Facility Layout Problem  of An Industry in Bangladesh                                                                                  Subrata Talapatra (KUET, Bangladesh) Tarapada Bhowmick (KUET) Kazi Arif-Uz-Zaman (KUET) 

IE-20

Application of Fuzzy Logic in Aggregate Production Planning

Md. Mohibul Islam (RUET, Bangladesh) Khan Md. Ariful Haque (RUET) Md. Mosharraf Hossain (RUET) Md. Ahsanul Haque Khan (RUET) Md. Rokebul Islam (RUET)

IE-21

An Efficient Supply Chain in Apparel Industry                                                    Shibbir Ahmad (BIM, Bangladesh) M. Iqbal (SUST, Bangladesh) Salma A. Iqbal (SUST) M. Roomi (Bangladesh)    

IE-30

Characterization of Calcined Sugarcane Bagasse Ash and Sugarcane Waste Ash for Industrial Use                                                                                               Mst. Shanjida Sultana (BCSIR, Bangladesh) Md. Aminur Rahman (BCSIR)    

IE-33

Analysis and Treatment of Waste Water of Textile Dyeing Industry: Study On Bulbul Textile, Kushtia, Bangladesh                                  

S.M. Hasan  Razu (KU, Bangladesh) Abul Kalam Azad (ESD, Khulna, Bangladesh) Quazi Hamidul Bari (KUET, Bangladesh) Masudur Rahman (ESD)

IE-38

Investigation of Powder and Binder Mixing Mechanism in Metal Injection Molding

Altab Hossain (UM, Malaysia) I. A. Choudhury (UM) M. Azuddin (UM) C. X. Yun (UM)

Paper ID

Technical Session – VII

Related Technology-I

01 November 2013 Friday 4:15-6:30 PM

Venue: Room # C

Chair: Prof. Dr. Syed Abdul Mofiz (RUET, Bangladesh)

Co-Chair: Prof. Dr. N. H. M. Kamrujjaman Sarker

Page #

      RT-03

Sea-Level Extremes and Change- Example of Bangladesh

Cansu Karsili (LU, Sweden) I. B. Muhit (CUET, Bangladesh) Mohammad Emdadul Hoque (LU, Sweden) Sohidul Islam (LU, Sweden)

      RT-05

Analyzing Energy Drinks Effect on Respiratory and Cardiac Function by Wavelet Transforms Using Laser Doppler Flowmetry

Md. Nafiur Rahman Protik (HMDSTU, Bangladesh) Fatema Khatun (HMDSTU, Bangladesh) Muhammad Muinul Islam (KUET, Bangladesh)

      RT-06

Better Understanding of Food Material on the Basis of Water Distribution using Thermogravimetric Analysis                                                                 Mohammad U. H. Joardder (QUT, Australia)  M.A. Karim(QUT, Australia) Chandan Kumar (QUT, Australia)

       RT-09

Study of Soil Properties and Evaluation of Evapo-transpiration for Wheat by Soil Moisture Depletion Studies

H. M. Rasel (RUET, Bangladesh) B. Ahmed (RUET) M. R. Hasan (RUET) M. S. U. Miah (RUET)

      RT-10

Wastewater Quality at Different Stages of Decentralised Waste water Treatment Process in the Peoples Panchtala Colony at Kalishpur, Khulna

Shuma R. Saha (KUET, Bangladesh) Muhammed Alamgir (KUET)

RT-11

A Survey of Different Types of Mask Available in Market and Development of a New Mask to Resist Particulate Emission

Md. Abdur Rahim (RUET, Bangladesh), Md. Shamim Akhter (RUET) S.M. Rasid (RUET) Md. Shahadat Hossain (RUET) Md. Sheikh Farid (RUET)

      RT-13

Improved Underground Mine Design for Reducing Subsidence at Barapukuria Coal Mine, NW Bangladesh

S    Syeda Musarrat Jabin (JSTU, Bangladesh) Kamruzzaman Miah (JSTU)                                                                                           Md. Hafizur Rahman (JSTU) Md. Abdullah-Al-Josi (JSTU) Md. Minhaj Uddin Monir (JSTU) H. M. Zakir Hossain (JSTU)

RT-15

People’s Perception on Environment in Urban Areas: A case Study on Dhaka City

Md. Shahidul Islam  (PC, Bangladesh) Md. Masud Rana(PC) Raquib Ahmed (PC) 

       RT-17

Assesment of Supplied Water Quality of Khulna WASA Of Bangladesh Kanij Fahmida (KUET, Bangladesh) Md. Hasibur Rahman Lemon  (KUET) Md. Saiful Islam (KUET) Md. Abdul Kader (KUET)

      RT-19

A Study or Heavy Minerals Resereve and Seperation Forces from Raw Beach Sands Along the Coastal Belt of Bangladesh

Mohammad Islam Miah (CUET, Bangladesh)

      RT-20

Color Strength Modeling of Knitted Fabrics Using Fuzzy Logic Approach

Ismail Hossain (UM, Malaysia) Altab Hossain (UM) I. A. Choudhury (UM) A. Bakar (UM) A. Shahid (DUET, Bangladesh)

RT-26

An Assessment of Subsidence due to the Extraction of 1203 Slice with its Associated Factors in the Barapukuria Coal Mine, Bangladesh

M. Farhad Howladar (SUST, Bangladesh) Kamrul Hasan (SUST)

Paper ID

Technical Session – VIII

Material Science-II

01 November 2013 Friday 4:15–6:30 PM

Venue: Room # D

Chair: Prof. Mohd. Sapuan Salit  (UPM, Malaysia)

Co- Chair: Prof. Dr. Khandkar Aftab Hossain (KUET, Bangladesh)

Page #

MS-01

In Situ Synthesis of Ferrites Nano  Particles Using Sono Chemical  Route                                                                                                     P. P. Goswami (IITG, India) H.A. Choudhury (IITG) S. Chakma (IITG) V. S. Moholkar (IITG)

MS-02

Influence of Porosity on Flexural Strength and Flexural Modulus of an Eco-ceramic Membrane

Sujoy Bose (IITG, India)  Chandan Das (IITG)

MS-03

Effects of Deformation on Microstructure and Mechanical Behavior of Al-Cu Alloys

N. Nafsin (BUET, Bangladesh) H. M. M. A. Rashed (BUET )

MS-07

Effect of Cu in Al-Si Alloys with Phase Modeling                                                E. A. Ashrafi (BUET, Bangladesh) A. Hasan (BUET) H. M. M. A. Rashed (BUET)

MS-09

Structural Analysis and Mechanical Testing of Single Fiber from Ladies Finger Plant

S. Imam Hossain (BUET, Bangladesh) Mahbub Hasan (BUET)

MS-11

Corrosion Behavior of Different Percentage Al-Zn Galvanized Steel            Azrin Akhter Chowdhury (BUET, Bangladesh)

MS-12

Phase Evolution & Characterization of Spinel Ferrite (Oxide) Nanocomposite material prepared by Chemical Route

Soumya Mukherjee (Jadavpur University, India) Abhigyan Datta ( JU) Mrinal Saha (JU) Siddhartha Mukherjee (JU)

        MS-32

Evaluation of Stabilized Soil Blocks with the inclusion of ‘Plastic Fibre’ as Sustainable Building Material: A Complete Review                                              I. B. Muhit ( CUET, Bangladesh)

MS-33

Analysis of Order of Stress Singularity at a Vertex in 3D Transversely Isotropic Piezoelectric Dissimilar Bonded Joints

Md. Shahidul Islam (KUET, Bangladesh) Md. Golam Kader (KUET)

MS-36

Analysis of Moisture Absorption Effect on the Longitudinal Three Point Bend Properties of Jute Epoxy Composite Processed Under Modified Compression Molding Process

Md. Rashnal Hossain (KUL, Belgium)  Md. Aminul Islam (BUET, Bangladesh) Ayasha Akter Aart (BUET) Van Vuure (KUL, Belgium)  Ignaas Verpoest (KUL, Belgium)

MS-43

Effects of Internal Resistance on the Photovoltaic Parameters of Solar Cells

Robin Khan (RUET, Bangladesh) M.F.Hossain (RUET)

MS-46

Investigation of the Photovoltaic performance of Si-based solar cells under different Light Illuminations

Mst. Rebeka Sultana (RUET, Bangladesh) Md Faruk Hossain (RUET) Mst Hasnara Khatun (RUET)

Paper ID

Technical Session – IX

Applied Mechanics-II

02 November 2013 Saturday 10:50 AM – 1:00 PM

Venue: Room # A

Chair: Prof. Dr. Sayed Ali Mollah (KUET, Bangladesh)

Co-Chair: Prof. Dr. Md. Emdadul Hoque (RUET, Bangladesh)

Page #

AM-02

Imaging Problems of a Low Cost Finger Print Sensor & Adjusting Various Parameters for its Improvement

Amit Roy (RUET, Bangladesh) Md. Rokunuzzaman (RUET) S. M. Rasid (RUET) Md . M. Hasan (RUET) G. Azam (RUET) B. K. Sarker (RUET)

        AM-03

Design and Implementation of a Remote Controlled Robotic Arm Based on Industrial Application Perspective

Md. Bony Amin (KUET, Bangladesh) G.M. Sultan Mahmud Rana (KUET) Abdullah-Al-Farabi (KUET) A.M.M. Nazmul Ahsan (KUET) Md. Ahasan Habib (KUET)

AM-04

Hand Gesture Recognition by Artificial Neural Network                             Soumen paul (KUET, Bangladesh) Md. Abu Shahab Mollah (AUST, Bangladesh) Rajibuzzaman (KUET) Tanvir Ahmad (AUST)  Kazi Toufiqur Rahman (DIU, Bangladesh)

AM-10

Development of Autonomous Line Following Robots for Solving a Maze Problem.

Md. Rokunuzzaman (RUET, Bangladesh) Asif Ahmed Shishir (RUET) Md. Saeed Sharman  (RUET)  Amit Roy (RUET)

        AM-11

Development of a Multipoint Digital Thermometer by Microcontroller         Amit Roy (RUET, Bangladesh)  Md. M. Hasan (RUET) S. U. Ahmed (RUET) Md. Rokunuzzaman (RUET)

        AM-14

Design and Fabrication of a Model Remote Control Gun Fire                           Md. Tazul Islam (CUET, Bangladesh) Syed Al-Mamun (CUET) M Raisul Islam (AIUB, Bangladesh)

AM-15

Development of an Obstacle Avoidance System for Mobile Robot to Avoid Accident by Using Microcontroller

Md. Rokunuzzaman (RUET, Bangladesh) Amit Roy (RUET) S. M. Rasid (RUET) Md. Sumon Reza (RUET) Md. Anik Islam (RUET)

AM-21

PLC Based Automatic Railway Gate Control & Remote Monitoring System

Khandaker Marsus (RUET, Bangladesh) Md. Selim Habib (RUET) Mohammad Ezaz Hossain (RUET) Md. Reazuddin (RUET) Md. I.H. Bhuiyan (RUET)

Paper ID

Technical Session – X

Industrial Engineering - II

02 November 2013 Saturday 10:50 AM – 1:00 PM

Venue: Room # B

Chair: Dr. Ali Ahsan Talukder (Ex-Faculty, RUET)

Co- chair: Dr. Masahiro Nakajima (Nagoya University, Japan)

Page #

IE-09

Cell Formation in a Batch Oriented Production System Using a Local Search Heuristic with a Genetic Algorithm: An Application of Cellular Manufacturing System

Md. Ariful Islam (RUET, Bangladesh) Sarojit Kumar Biswas (RUET) Md. Rashedul Islam (RUET) Md. Mosharraf  Hossain (RUET)

IE-12

Application of Six Sigma Philosophy For Reducing Process Variability: A DMAIC Model

Akhtar Ferdous Khan Asif (RUET, Bangladesh) Ripon Kumar Chakrabortty (RUET)

IE-17

An Analytical Study of Hazards And Risks In Concern Of Shipbuilding Industry

Farjana Nur (KUET, Bangladesh) Dipa Rani Paul (KUET) Md. Ahasan Habib (KUET)

           IE-19

Implementation of Production Control Tools in Garments Manufacturing Process Focusing Printing System.

Md. Bony Amin (KUET, Bangladesh) Adnan Islam (KUET) Syimun Hasan Mehedi (KUET) Sahea Dul Bashar (KUET) Md. Ahasa Habib (KUET)

           IE-23

Simulation and Optimization of Natural Gas Processing Plant

Sukanta Kumar Mondal (SUST, Bangladesh)  M. Rakib Uddin (SUST) A. K. Azad (CQU, Australia)

          IE-27

Implementation of Lean Philosophy and Improvement of Sigma Level in Cutting Section According to DMAIC Approach                                                           Md. Morshedul Alam (RUET, Bangladesh) Md. Sanowar Hossain (RUET)

          IE-28

Effect of External Magnetic Field on Drilled Hole Quality During Drilling Operation

Anayet U. Patwari (IUT, Bangladesh) Shafi Noor (IUT) Md. S.I. Chowdhury (IUT) Towfiq ullah (IUT)

IE-29

Advanced Functionalization of Textiles by Nanofinishing: A Review                Md. Milon Hossain (KUET, Bangladesh) Md. Ahsanul Karim Biswas (TU, Germany) Md. Shohan Parvez (MBSTU, Bangladesh) Sudipta Bain (MBSTU)

IE-31

Smart Textiles-New possibilities in Textile Engineering                             Subrata Chandra Das (MBSTU, Bangladesh) Debasree Paul (MBSTU)  Sk. Md. Mahamudul Hasan (MBSTU) Nasif Chowdhury (MBSTU) Md. Eanamul Haque Nizam (MBSTU)

IE-34

Tribological Research and Industrial Applications in Bangladesh

Sobahan Mia (KUET, Bangladesh)  Md. Mahmudul Hassan (KUET) Dipayan Mondal (KUET)  and Muhsia Tabassum (KUET)

IE-39

Epistemic Uncertainty Study of the Conceptual Phase of Product Development by Multi-Valued Logic and Information Content

Md  Mamunur  Rashid (BIM, Bangladesh) AMM Sharif Ullah (KIT, Japan) Jun’ichi Tamaki (KIT) M.A Rashid Sarker (BUET, Bangladesh)

Paper ID

Technical Session – XI

Material Science-03

02 November 2013 Saturday 10:50 AM-1:00 PM

Venue: Room # C

Chair: Prof. M. Shahidur Rahman (RU, Bangladesh)

Co-Chair: Prof. Md. Abdul Maleque (IIUM, Malaysia)

Page #

        MS-04

Performance of Recycled Coarse Aggregate in Concrete Mix

B. Ahmed (RUET, Bangladesh) M. A. A. Mahmood (RUET) H. M. Rasel (RUET)

MS-06

Effect of Clay and Moisture Content on the Properties of Molding Sand

Tasmia Zaman (RUET, Bangladesh) M. A. A. Mahmood (RUET) A. Hafiz Zaman (RUET)

MS-08

Improved Dielectric Properties of La/Mn Codoped Bismuth Titanate Ceramic                                                                                                       M. S. Parvez (RU, Bangladesh) M. Bodiul Islam (RUET, Bangladesh)

        MS-18

Preparation and Properties of Chemically Reduced Cu and Ag

Nanoparticles                                                                                                        M. Julkarnain (RU, Bangladesh) Arup Kumar Mondal (RU) Md. Mizanur Rahman (RU) Md. Sohel Rana (RU)

MS-24

Micro Responses of Sheared Granular Materials using 3D DEM

Md. Mahmud Sazzad (RUET, Bangladesh) Toufiq-E-Alahy (RUET) Shashanka Biswas (RUET)

        MS-31

Friction Coefficient of Copper Mating with Smooth and Rough Mild Steel Counterfaces

Mohammad A. Chowdhury (DUET, Bangladesh ) D. Muhammad Nuruzzaman (UP, Malaysia) B. K. Roy (DUET) Rajib Nandee (EKCL, Bangladesh)

MS-35

Selection of Constitutive Models for Concrete in simulating Reinforced Concrete Members

Sharmin Reza Chowdhury (AUST, Bangladesh) Md. Shahid Mamun (AUST) Wahid Hassan (EUB, Bangladesh)

        MS-41

An Iteration Method for Near-tip singular fields of a crack in a Power- law Hardening Material Using Asymptotic Analysis

Md. Arefin Kowser (DUET, Bangladesh)  Md. Mahiuddin (DUET)

MS-42

Ceramics in Bangladesh: Its Recent Evolution and Future Prospect

M. A. A. Mahmood (RUET, Bangladesh) M. S. Rahman (RUET) Tasmia Zaman (RUET)

         MS-44

Implementation of Computer-controlled Electrodeposition Methodology for Depositing Metal Oxide Thin Films

Md. Hasibul Islam (RUET, Bangladesh) Md. Faruk Hossain (RUET) Shuva Paul (RUET) Mohua Fardousi (RUET)

MS-45

Investigation of Optical Properties of ZnO Thin Films Prepared by Sol-gel Method                                                                                                             Shuva Paul (RUET, Bangladesh) Md. Faruk Hossain (RUET)

  MS-47

Design and Fabrication of handmade screen printing for thin film applications

Hasnara Hasi (RUET,Bangladesh) Md. Faruk Hossain (RUET) Mst. Rebeka Sultana (RUET) Robin Khan (RUET) Hasibul Islam (RUET)

Paper ID

Technical Session – XII

Energy Technology-II

02 November 2013 Saturday 10:50 AM- 1:00 PM

Venue: Room # D

Chair: Prof. M.N.A. Howlader (IIUM, Malaysia)

Co-Chair: Prof. Dr. Md. Rafiqul Islam Sheikh (RUET)

Page #

          ET-05

Effect of Energy Efficiency Design Index on Container Vessel Design        Md. Shahjada Tarafdar (BUET, Bangladesh) S M Rashidul Hasan (SNAL, Bangladesh)

ET-06

Design and Development of a Vertical Axis Low Speed Wind Generator

Mr. Rupesh Chandra Roy (BCSIR, Bangladesh) Most. Hosney Ara Begum (BCSIR) Muhammad Riazul Hamid (AUST, Bangladesh)

         ET-07

Energy Saving Brick from Rice Husk Ash                                             Md.Latiful Khabir (BUET, Bangladesh) Md. Masrul Huda (BUET) Ruhul Amin (BUET) Sarker kamruzzaman (BCSIR, Bangladesh)

          ET-09

Better Energy Utilization : A Solution of Power Crisis in Bangladesh

Omar Faroque (NU, Bangladesh) Mahadi Hasan Masud (RUET, Bangladesh) Mohammad U. H. Joardder (QUT, Australia)

         ET-16

Modeling and Optimization of Variable Speed Wind Turbine Using Permanent Magnet Synchronous Generator

M.R.I. Sheikh (RUET, Bangladesh) Zinat Tasneem (RUET)

         ET-18

Design, Fabrication and Performance Study of a Plastic Waste to Oil Converter

Asma-Ul-Husna (RUET, Bangladesh) Farzana Nahid (RUET) Shahina Imam (RUET) Mohammed Rofiqul Islam (RUET) M. A. Kader (RUET)

         ET-22

Modeling and Controlling of Directly Driven Wind Turbine with Permanent Magnet Synchronous Generator

M.R.I. Sheikh (RUET, Bangladesh) Zinat Tasneem (RUET)

          ET-23

Prospects of Bagases Gasification Technolgoy for Electrcity Genration in Sugar Industries in Bangladesh

Barun Kumar Das (RUET,Bangladesh) S.M. Najmul Haque (RUET) Md. Sazan Rahman (RUET) M.A. Kader (RUET)

ET-26

Study of Pyrolysis Products-Оil-Bitumene Rocks Western Kazakhstan

M.N. Abdikarimov(KazNTU)  R.H. Turgumbaeva (KazNPU)

         ET-31

Characterization and Improvement of Char Product Obtained from Pyrolysis Conversion of Solid Tire Wastes into Liquid Fuel

M.S. Hossain (RUET, Bangladesh) M.R. Islam (RUET) H. Haniu (KIT, Japan)

ET-33

Power Factor Improvement of Compact Fluorescent Lamp                   Mamun Hossen (RUET) Md. Zillur Rahman (RUET) Julkar Nain (RUET)

Paper ID

Technical Session – XIII

Related Technology- II

02 November 2013 Saturday 2.00 PM – 4.00 Pm

Venue: Room # A

Chair: Prof. Dr. Tarif Uddin Ahmed (RUET, Bangladesh)

Co-chair: Dr. Kamruzzaman (RUET, Bangladesh)

Page #

RT-04

Group Velocity Dispersion Analysis of Rajshahi Earthquake for Studying the Crustal Thickness

Md. Omar Faruk (RU, Bangladesh ) Syed Mustafizur Rahman (RU)Md. Abul Hashem (RU) Mumnunul Keramat (RU, Rajshahi)

RT-08

Effects of Soil Salinity on Crop Production rate of the South West Zone of Bangladesh

B. Ahmed (RUET, Bangladesh) H. M. Rasel (RUET) M. R. Hasan (RUET) M. S. U. Miah (RUET)

RT-12

Environmental Impact Assessment of Madhyapara Granite Mine, North West  Bangladesh

Md. Nahid Nowsher (JSTU, Bangladesh) H. M. Ratul-Al-Istiak (JSTU) Tanvir Rahman Mahid (JSTU) Bapi Biswas (JSTU) S. M. Azmol Huda (JSTU) Mohammad Tofayal Ahmed (JSTU)  H.M. Zakir Hossain (JSTU)

RT-16

Impact of Climate Change on Water Supply and Sanitation: A Case Study in Char Area

Selim Ahmed (KUET, Bangladesh) Kh. Mahbub Hassan (KUET) Md. Hasibur Rahman Lemon (KUET)

RT-18

Evaluation of Subsurface Geologic Formation in the Barind Tract, Rajshahi, Bangladesh

M.A.F.M. Rashidul Hasan (RU, Bangladesh) R. Yasmin (RU, Bangladesh) S. Shahid (UTM, Malaysia) Mumnunul Keramat(RU, Bangladesh)

RT-22

Study of River Bank Sedimentation Using Permeable Structural Measures

Md. Lutfor Rahman (RRI, Faridpur, Bangladesh) Md. Showkat Osman (DUET)

RT-23

Zinc Calume Profile Steel Sheet for Roofing Element

S. M. Zahurul Islam (RUET, Bangladesh) Abang - Abdullah Abang Ali (UPM, Malaysia)

RT-25

Strip Tillage Seeding Technique: A Better Option for Utilizing

Md. Israil Hossain (RWRC, Bangladesh)  M. K. Gathala (RWRC Bangladesh) T.P. Tiwari (CIMMYT ,Bangladesh)

Paper ID

Technical Session – XIV

Poster Session

02 November 2013 Saturday 2.00 PM – 4. 00 PM

Venue: GCE Building

Page #

AM-P06

Advance Railway Control System

Md. Rokibul Hossain (RUET, Bangladesh) Md. Sharafat Ali (RUET) Md. Nazmul Haque (RUET)

AM-P17

Automation of Belt Conveyor for Carrying Products

Shah Ali Mollah (KUET, Bangladesh)  Md. Sihabun Sakibul Haque (KUET) Aminul Islam (KUET) Md. Zahid Hossain (KUET) Farjana Nur (KUET)  Dipa Rani Paul (KUET)

AM-P19

Program for Control and Operation of PUMA Robot by ‘C’ and Microcontroller                                                                                     Tasnuba Binte Nur (CAT, Dhaka, Bangladesh)

ET-P08

Reducing the Wastage of Water by Efficient Water Faucet

Ifrat Jahan Tisha (AUST, Bangladesh) Nafis Faiyaz (AUST) Moniruzzaman Peash (AUST)

ET-P11

Acquisition of Sustainable Economic Growth through Proper Utilization of Renewable Energy Sources – A Study on Various Aspects, Challenges and Prospects of RE in Bangladesh

Hosnay Nasrin (NU, Bangladesh)

RT-P01

An Overview of Control Systems applied to a Gas Process Plant

Mohammad  Ariful Islam (SGFL, Sylhet, Bangladesh)

RT-P02

A Comparative Study of Instrumentation Systems of a Gas Process Plant

Mohammad Ariful Islam (SGFL, Sylhet, Bangladesh)

RT-P21

Effect of Climate Change on the Coastal Area in Bangladesh                          S.M. Abdullah Al Faruq (KUET, Bangladesh) Md. Zohrul Islam (KUET) Hasan Mahmood (KUET)

RT-P24

Water Quality in Market Drains of Khulna City Area: Sustainable Market Waste Management Perspective

Md.Atiqur Rahman (KUET,Bangladesh) Kh. Mahbub Hassan (KUET) Md. Iftekar Alam (KUET) Md. Abdul kader (KUET)

TE-P10

Room Heating by Energy Transfer and its Performance                                     Md. Foysal Ahmed (CUET, Bangladesh) K. M. Anamul Hossain (CUET) A. Z. M. Shariful (CUET)

ET-P10

A solution to the power crisis using the coastal zone of Bangladesh

K.M. Masnoon Haider (UAP, Bangladesh) Arnob Saha (UAP) Md. Tohidul Islam (UAP)

ET-P19

Feasibility of Wind Power Technology Schemes in St. Martin’s Island of Bangladesh

Rasedul Hasan (BU, Bangladesh) Md. Abu Saaklayen (BU) FarjanaNasim (BU) Md. Tajul Islam (Samsung R & D center, Bangladesh) Md. Abu Shahab Mollah (AUST, Bangladesh)

IE-P03

Customer Behavioral Segmentation at Banking System using Principal Components Analysis and Artificial Neural Network: The Quality Management

Md.Sarwar Kamal (TUB, Chittagong, Bangladesh) Mohd. Kamal Uddin (TUB)

IE-P04

A Case Study: Supply Chain Uncertainities and Required Integration Based on Shared Resources in The Chemical Industries

Abu Md. Saifuddoha (KUET, Bangladesh) Md. Saiful Islam (KUET) Mahabubur  Rahman (KUET) Kismot Abdul Quayum (KUET)

IE-P06

Development of Human Machine Interfacing (HMI) Software for

Force Circulated Wood Pulp Digester

Rupesh Chandra Roy (PP & PDC, Bangladesh) Sarker Kamruzzaman (Bangladesh) Md. Badrul Abedin (Bangladesh)

IE-P07

Application of Value Stream Mapping in Cement Industry’s Supply Chain and Analyzing Results by Fuzzy Inference System

Abu Md. Saifuddoha (KUET, Bangladesh) Md. Ahasan Habib (KUET) Sohana Yasmin Sumi (KUET)

IE-P13

Operation Management Techniques & Applications in Bangladeshi Industry

Kazi Arif-Uz-Zaman (KUET, Bangladesh) Md. Ahasan Habib (KUET)Md. Abdur Rauf (KUET)

IE-P14

Opportunities for Lean- Six Sigma in Bangladeshi Industry

Kazi Arif-Uz-Zaman (KUET, Bangladesh) Md. Ahasan Habib (KUET) Kazi Saifuzzaman Palash (KUET) Mahmud Parvez (KUET)

IE-P15

Recent Trends and Issues of Sustainability in Battery Manufacturing Industries of Bangladesh

Kazi Arif-Uz-Zaman (KUET, Bnagladesh)Md. Ahasan Habib (KUET) Subrata Talapatra (KUET) Mostafa Lutfi (KUET) Md. Enamul Kabir (KUET)

IE-P16

Development of Adjustable Pattern for Foundry Shop

Shah Ali Mollah (KUET, Bangladesh) Md. Jannatul Ferdouse (KUET) Rezaur Rahman Rakib (KUET)

IE-P25

Recycle of Waste Polythene and use this Recycle Polythene to Produce Construction Block                                                                                Most. Hosney Ara Begum (BCSIR, Dhaka, Bangladesh) Mr. Rupesh Chandra Roy (BCSIR) Nahid Sharmin (BCSIR)

IE-P36

Assessment of Environmental Pollution of Gaseous Emissions of Chemical Plants by Mathematical Modelling

R.H. Turgumbaeva (KazNPU) M.N. Abdikarimov(KazNTU)

IE-P37

Quantification and Physical Categorization of Waste Generated by Different Healthcare Entities in Chittagong Metropolitan Area, Bangladesh

Ohidul Alam (CU, Bangladesh) Mohammad Mosharraf Hossain (CU)